Call us: 1.888.880.4884 Guest # 0

For those who are on the fence about the costs and benefits of a do-it-yourself project, here's the simple fact: add up the time and money involved in making your own, and you'll see that it's a better deal to buy one rather than make one. Of course if the challenge and experience of doing it yourself is important to you, time and cost shouldn't be a deterrent. But if you're an enthusiast who's swayed - pun intended - by facts and figures, consider the following:

Add up the cost of cord (about $13 to $13.50/pound), a giant netting shuttle (about $7.50), a piece of lumber for making two hardwood bars (roughly $5 for a 2x4), rings (a pair for $2.50ish), and you're out about $55 for materials if you're making a two-person design. The cost of our most affordable models at Hayneedle.com? Less than $60. Even a cheap DIY backpacker's hammock will cost about $20 in materials, plus a lot of time spent hemming and sewing with a sewing machine.

Take a look at our selection under $50. Once there, the "Sort By" feature in the top right corner lets you view them in order of price.

Materials You Need
One Person Hammock Two Person Hammock
2 pounds of Cord 3 pounds of Cord
1 Gauge Stick 1 Gauge Stick
1 giant Netting Shuttle 1 giant Netting Shuttle
2 Hardwood Bars 2 Hardwood Bars
1½” x 1½”, 33" long 1½” x 1½”, 48" long
33" long 48" long
2 Rings, 2”-3" diameter 2 Rings, 2"-3" diameter
Step 1

START: Cut a three-foot piece of twine; square knot the ends. Hang the loop from a handy nail, hook, or door knob.

Make Your Own Hammock Square Knot
Step 2

WIND: Load shuttle with cord (see pictures). Not too full for the first row. Tie free end to the loop.

Use a Shuttle to Make Your Own Hammock
Step 3

CASTING ON: Hold gauge stick in your left hand. Wrap the shuttle cord once around the stick-down in front and up behind. Pull the shuttle up through the starting loop. Holding shuttle cord loop tight around the gauge stick, half hitch around both sides of the starting cord. Repeat, until you have made 20 loops around the gauge stick (30 for a two-person design). Pull snug and even out.

Weaving Your Own Hammock
Step 4

FIRST ROW: Pull out the gauge stick. Rotate the work, so the shuttle is on the left side. Hold the gauge stick in your left hand, just under the work. Bring the shuttle cord down in front, up behind gauge stick, through the first loop, and around the loop in a half hitch. Repeat, through each loop in turn, evenly.

Step 5

ADDING TO SHUTTLE: Soon, your shuttle is going to be exhausted. Reload, as above. Wind on as much as the shuttle will take. Knot the free end to the end of the old cord with a square knot.

Step 6

SECOND ROW: Rotate the work, so the shuttle cord is on the left. Proceed as for first row. Repeat until done. Fifty-four rows are about seven feet. Work longer or shorter.

Step 7

ALONG THE WAY: Any time after the second row, cut your starting cord and pull it free from the top row of loops. Support the piece as you add rows by any convenient means that holds it evenly - a dowel threaded straight across a row of loops, for instance.

Step 8

MOUNTING: Drill 20 holes (30 for a two-person design) through each 1½” by 11/2" hardwood bar, 1½” apart from center to center and 2¼" in from each end. Make the end holes 1/4" to 5/16" diameter, the rest from 3/16" to 1/4" diameter. Cut forty 50" long cords, twenty for each end (sixty for a two-person). Loop the first cord through a ring, thread both ends through left hand hole in hardwood bar. Overhand knot through top left hand loop in the net. Fasten each cord, in turn, through bar to loops in net. Do both ends.

Make Your Own Hammock with Spreader Bars
Step 9

SIDE BRAIDS: You need the net to sag in the middle so it holds a body snug. Make two 3-cord braids 3" shorter than the stretched out length of the hammock net, one for each side. Remember that braids end up about 10% shorter than their component cords, so cut generously and trim later. Thread one end through the outermost hole in support bar. Secure with an overhand knot. Weave in and out through the outside meshes. Thread through the bar at the far end, the outside hole, and secure with overhand knot. Repeat on other side.

Make Your Own Hammock with Side Braids
Hammocks
1-888-880-4884
GUEST#   0
Customer Service:
9AM-10PM ET, Mon - Fri
10AM-6PM ET, Sat
Sales Assistance:
8AM-12AM ET, Mon - Fri
9AM-12AM ET, Sat - Sun
Hayneedle, Inc., Internet Shopping, Omaha, NE
Copyright 2002 - 2014, Hayneedle Inc., all rights reserved.